VME-5531L - VMIC VME-5531L VMEbus - Fiber-Optic Repeater Link Simple Type: Repeater...
- Part Number:
- VME-5531L
- Model Number:
- VME-5531L
- Make:
- VMIC
- Lead Time:
- Available
- Qty In Stock:
- Available
VMIC VME-5531L VMEbus - Fiber-Optic Repeater Link Simple Type: Repeater Link
The VMIVME-5531 Link is a high-performance, yet easy-to-use method of linking two or more VMEbus systems together via fiber-optic cable. The Repeater Link is a two-board set which allows VMEbus slave I/O boards residing in one VMEbus chassis to be controlled by a VMEbus master residing in another chassis. The VMEbus chassis in which VMEbus masters reside is referred to as a primary chassis, while the VMEbus slave boards reside in a secondary chassis. The two-board set is configured as shown in Figure 1 with one board designated for the primary chassis while the other board is designated for the secondary chassis.
For Resellers and High Volume Orders:
Please request a quote to obtain preferred pricing.
Features
- Advantages Over Standard Repeaters (Small Cables. High-Noise Immunity. High-Voltage Isolation. No EMI Generated by Cables)
- High-Performance, Easy-to-Use Method of Linking Two or More VMEbus Systems Together Via Fiber-Optic Cable
- Maximum 6,560 feet (2,000 m) Fiber-Optic Cables
- Plug-and-Play Operation
- Refer to VMIVME-201 for 21-Slot 3U Chassis
- Software Transparent Allows Direct Communication from Primary Chassis to Secondary Chassis with No Software Overhead (Unidirectional Link Control with Bidirectional Data Transfers)
- Supports 16-, 24-, and 32-bit Addressing (6U Slave)
- Supports 8-, 16-, and 32-bit Data Transfers (6U Slave)
- Supports 8-, 16-bit data, 16-, 24-bit Address (3U Slave)
- The VME-to-VME Link Consists of Two Boards and Two Fiber-Optic Cables (Master Board: 6U, Slave Board: 6U or 3U)
- Total Electrical Isolation Between VMEbus Systems
Specifications
- Address Modifiers: (09, 0D) 3, 29, 2D, 39, 3D
- Altitude: Operating: 0 – 10,000 ft (3,000m)
- Bandwidth at 1,300 nm: 500 MHz-km
- Boot Length: 20 to 60mm
- Buffer Size: 900 micron
- Clad Size: 125 micron
- Connector Style: ST, 2.5mm Bayonet, both ends
- Cooling: Forced air convection
- Dimensions: Double height (6U) board 160 x 233.35mm or single height (3U) board 160 x 100.0mm (Slave only)
- Fiber Size: 62.5 micron
- Form factors: double height, single slot: 5531M | double height, single slot: 5531S | single height, single slot: 5531S
- Humidity: Operating: relative humidity 20% to 80%, noncondensing
- Length: 5 to 6,560 ft (1.5 to 2,000m)
- Maximum Attenuation at 1,300 nm: 9.0dB (including connectors)
- Mode: Multi
- MTBF: 431,525 hours
- Power Requirements: VMIVME-5531S: 2A typical at 5VDC 3.0A maximum | VMIVME-5531M: 2A typical at 5VDC 3.0A
- Quantity Required: 2 per link
- Read Cycle Overhead: 4.0µs maximum.
- Temperature: Operating: 0 to +65° C | Storage: -20 to +85° C
- Transfer Rate (Maximum) (10-foot Cable Length): Assuming a slave board in the secondary chassis responds in 250ns: 1 Mbyte/s minimum (D32) Note: Applies to 6U.
- U.L./NEC Rating: OFNP
- VMEbus Compliance: Complies with VMEbus specification revision C.1 | A32, A24, A16: D32, D16, D08 (EO) | VMIVME-5531M is DTB slave (for use in Primary Chassis)
- VMEbus Signals Repeated to Secondary Chassis: A1 to A31, D0 to D31, DS0*, DS1*, WRITE*, SYSRESET*, AM2, AM4, AM5, and LWORD*
- VMEbus Signals Returned to Primary Chassis: (D0 to D31, DTACK*)(D0 to D15, DTACK*)
- Write Cycle Overhead: 4.0µs maximum.
Applications
- None Available
Aliases
- None Available
Related Items
VME-5504L
VMIC VME-5504L VMEbus - D32/A16 RS-485 Multidrop Repeater Link
VME-5510L-XX
VMIC VME-5510L-XX VMEbus - Multimaster Repeater Link
VME-5532L
VMIC VME-5532L VMEbus - Fiber-Optic Repeater Slave Chassis System Controller
VME-Repeat L
High Performance Repeater Link